Windsor STORM SP20 Manuel d'utilisateur

Operating Instructions (ENG) MODELS: SP13 SP17X SP15 SP20X SP17 SPDS20 SP20 Read these instructions before using the machine.FLOOR POLIS

OPERATIONSTORM POLISHER 980100 03/08/032-3CONTROLS1. Safety Lock – Prevents unintended operation of themachine.2. Switch Levers – Turns machine on

OPERATION ! CAUTION For indoor use only. To prevent possible damage to the floor when using the brush option, use water or other approved cleaning sol

MAINTENANCE SCRUB BRUSHES NOTE: All original equipment brushes are equipped with “Perform Alert�”. This feature will tell the operator when it is ti

TROUBLESHOOTING PROBLEM CAUSE SOLUTION Machine will not run Circuit breaker tripped in building. Check and reset. Power switch failure. Test switch

BRUSH/PAD DRIVER GROUP 1A 1B 1D 1C 3 3 2A-W STORM POLISHER 980100 04/24/06 3-1

BRUSH/PAD DRIVER GROUP REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1A 02216 - PAD DRIVER, 13" POLISHER 1B 02396 - PAD DRIVER, 15&quo

FRAME GROUPSTORM POLISHER 980100 03/08/033-31415162117D17B17C17AMOTOR ASMSEE PG 3-518C18D18A18B19201213118104657322232189

FRAME GROUP REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 78447 1 TUBE ASSY, HANDLE ADJ 2 38290 1 HANDLE, POLISHER 3 57275 1 NUT,

MOTOR GROUPSTORM POLISHER 980100 03/08/033-5SP13, SP15, SP17, SP20931124SP17X, SP20X7SPDS20121181012111415126

MOTOR GROUP REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 27884 1 COVER, MOTOR 2 500763 1 LABEL, STORM MAIN 3 53263 1 MOTOR, 1 HP

For the name and address of your dealer contact: Windsor Industries___________________________________________________________________________________

HANDLE GROUP STORM POLISHER 980100 03/09/05 3-7 111201225141361718371991584102122169

12345678910111213141516171819202122HANDLE GROUP REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 14344 1 BAR, HANDLE ADJUST 140393 1 BLOCK,

WIRING GROUP STORM POLISHER 980100 11/15/03 3-9 846211611311097512PRIOR TO SN *

WIRING GROUP REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 20054 1 CLAMP, 3/8 NYLON UL/CSA 2 23167 1 CORD SET, 14/3 STO X 50' YLW

WIRING DIAGRAM / SPARE PARTS SUGGESTED SPARE PARTS PART NO. DESCRIPTION SERIAL NO. FROM NOTES: 87202 WASHER, BEARING (HANDLE ADJ) 73990 SPRING, EXT

TABLE OF CONTENTS Machine Data Log/Overview. ...2 Table of Contents ...3 HOW TO USE THIS

________________________ ____________________________ ___________________ ______________________________ __________________ HOW TO USE THIS MANUAL Thi

IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCT

HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three

THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp

TECHNICAL SPECIFICATIONS ITEM DIMENSION/CAPACITY Construction Heavy-duty die cast aluminum deck with heavy-duty rubber bumper, tubular steel adjusta

HANDLE INSTALLATIONSTORM POLISHER 980100 03/08/032-2The machine is shipped with handle unassembled.Follow these steps for installation:1. Remove ha